Archive | October 2009

October Ornament and More 2009 Ornament Finishing

Friday I got the accessory kit I ordered for the Victoria Sampler Gingerbread Scissor Keep published in the 2009 JCS Ornament magazine.  I managed to stitch and finish it up over the weekend!  I used the template provided in the magazine for the final shape of it, but just finished as an ornament and not as a scissor keep.  On this one, I really wanted to join the cording at the base, but couldn’t figure out how to do it and have it look nice, so this ornament ended up with a tassle:

2945794240029744911lNEgdi_fs
Victoria Sampler Gingerbread Scissor Keep

While I had my finishing supplies out, I decided to finish one more ornament that I’d stitched earlier in the year:

2815952380029744911sMYOZS_fs
Just Nan A Little Joy

So… I’m approaching the end of my 2009 Ornament Project.  I have two more ornaments to stitch and finish, then one last stitched ornament that needs to be finished up!

Advertisements

September Ornament and Ornament Project Update

I finished up my September ornament over the weekend!

2229956040029744911yRdkyy_fs

2660900800029744911ZcZbcQ_fs
Sweetheart Tree’s Stichers Favorite Scissor Fob Front and Back

I also did some finishing of ornaments I stitched earlier in the year:

2639122000029744911zlDELF_ph

2650766540029744911lQqCED_ph

The Prairie Schooler’s Snowy Night Front and Back

2393177280029744911yblJoq_ph

2961926400029744911XECgTZ_ph
Country Cottage Needlework’s Snowy Eve Front and Back

Plus I finished the Brittercup Poinsettia in the previous post. So, for my 2009 Ornament Project, I have three more to stitch and two that just need to be finished.

How To Finish an Ornament Using Aluminum Ornament Forms

Have you ever avoided stitching a round ornament because you weren’t sure how you were going to finish it??  Aluminum ornament forms are the solution…  its super easy to do and they always look great, and more importantly, perfectly round, when you’re finished.

2430737260029744911KHKoEK_fs
Ornament Forms

I’ve seen these at a couple of different LNSs.  I most frequently buy them from The Silver Needle in Tulsa, but I also know that House of Stitches carries them too.

I was finishing up some ornaments today and thought I’d take some pics of how I used the ornament forms for anyone who is curious about trying these out.

You Will Need:

  • Stitched ornament
  • Pair of ornament forms  that fit the stitched piece
  • Backing Fabric
  • Thin batting
  • Tacky Glue
  • Strong thread and a needle (I usually use #8 perle cotton)
  • Trim (ribbon or cording)

I like my finished ornaments to have a little padding, so I squirt some glue on the convex side of the ornaments, stick some rough cut batting on them, then trim away the excess batting using the outside of the form as a guide:

2273817240029744911lyCPTg_fs

2775135220029744911YgxIXa_fs

Using your ornament forms as a loose guide, trim both your backing fabric and your stitched ornament to about 3/4″ beyond the circumference of the ornament form.

Thread your needle with some sturdy thread (I use perle cotton) and stitch a running stitch near the edge of your trimmed fabric.  As you can see from my pic below, there’s no need to create a perfect circle with your running stitch or even have the stitches be nice and even!  When finished, make sure that the tails of your thread end up at the front of your stitched piece.

2402321130029744911ANFLeT_fs

Next, place one of the ornament forms, batting side down, on the back of your stitching. Do your best to center the form on the stitching.  Pull the tails of the running stitch to cinch up the fabric around the form. Think of it kind of like cinching up a draw string bag. Tie the tails with a square knot, then put a little dab of glue over the knot:

2711778690029744911fBbZRm_fs

Turn the form over and make any small adjustments needed to be sure the stitching is centered on the ornament form.  The batting should be betwen your stitching and the convex side of the ornament form.

Do the same with the backing fabric on the other form:

2728969210029744911ZfeeHG_fs

Don’t worry about the fabric bulk created by the cinching. Because the ornament forms have a rounded surface, there is plenty of space for the fabric bulk to be contained within the hollow space at the center of your ornament.

Next, dab a small amount of glue around the edge of the form that is fitted with backing fabric:

2306673170029744911JXZljb_fs

Pick up both halves of the ornament and line the edges up and press firmly together. If you want a ribbon hanger (click here for a pic of ornaments that I finished this way), you would want to slip the ends of the ribbon at the top of the ornament before pressing together. I chose cording for this ornament, so no need for this step:

2542487700029744911QRryQX_fs

Wipe away any excess glue then put the ornament under a book or other heavy object for the glue to set.

Twisted cording is the next step. I make a little puddle of glue on some scrap paper or fabric, then use the end of a pin to run glue along the seam between the back and front of the ornament. Using the pin helps you avoid putting too much glue that will squeeze out from under the cording, and also gives you more control over where the glue goes.

Arrange your cording around the ornament, leaving room at the top to create a hanger, and gently run the cording along the glue line between the front and the back of the ornament:

2704944540029744911buJYAe_fs

Take some thread that matches your cording and wrap around the cording at the base of the hanger and the point where the cording joins at the bottom of the ornament. This helps secure the tension on the cording while the glue sets and also just looks nice. 🙂

Clip the ends of the cording at the bottom then untwist and separate the threads to make a tassle.  Trim the tassle threads so that they are all the same length:

2711050510029744911jybzRN_fs

You are finished!